The original lamp is rated at 125V, which would make it last somewhat longer operating at a nominal 120V. You could go with the 120V lamp, but you might see slightly shorter life.
Can you plug 120V into 125V?
2 Answers. 120v and 125v outlets are nominally identical. You must have something miswired, or you have a rare faulty unit. Be sure you have power connected to the LINE side.
What happens if you use the wrong voltage light bulb?
Using a light bulb with too high of wattage can lead to overheating of the light bulb. This heat can melt the light socket as well as the insulation of the wires. Once that happens, you put yourself at risk of arc faults, and this is something that could even lead to property fires.
Can I use a 120V bulb in a 110V socket?
Products rated at 110V, 115V, 117V and 120V are considered interchangeable. And the power coming from your wall socket ca vary between about 107V to 123V depending on the power draw at the time in your area. Yea, there is no difference.
Can any bulb go in any socket?
Yes, you certainly can use bulbs of different wattages in your fixture. The fact that one socket pulls more current is not important. Bulb size is mostly a matter of light distribution and heat management. It’s not relevant here as long as you don’t have them up against something flammable or enclosed too tightly.
Why do outlets say 125V?
They are rated for 125 VAC so that they don’t break down when exposed to 120 VAC continuous mains voltage. If you planned to drive your car at up to 120 mph you would buy tires rated for at least 125 mph, right? The 125 volt marking does not indicate the actual voltage present but is an electrical rating of the plug.
What is a 120V outlet?
The common 15 amp, 120 volt household outlet (also called a receptacle) is used throughout North America. Lamps, vacuum cleaners, refrigerators, etc. plug into it. The outlet has two vertical slots; the U-shaped hole is for the green safety grounding wire.
Can I use a 120 volt bulb in a 250 volt socket?
The fixture can handle anything up to 250V. You can use a 120V bulb. … The maximum voltage is the highest that the fixture is rated to endure.
Can you use 120V bulb in 130V socket?
For example 120V and 130V bulbs are interchangeable and the pros in using a 130 Volt bulb are: cooler burning bulb, less energy use, longer life and better handling of voltage surges. The cons are lower lumens output (not as bright) and lower color temperature.
Is 120V low voltage?
120V (also known as high voltage) is full line power and when used for outdoor lighting is quite costly. The initial cost for the installation can be 2-3x the cost of 12V (also known as low voltage).
Are 110v and 120v the same?
Sometimes you may hear 110 volt plugs referred to as 120 volt. Do not be confused by this; think of them as one and the same. There are a few variations of the 110 volt outlet based on the size of the breaker associated with the circuit, which is measured in Amps. The 2 most common variations are 15 Amp and 20 Amp.
Can I use 110v for 120v?
Can I Use 110v in a 120v Outlet? You can use a 110v appliance in a 120v outlet. The differences between 110 and 120v are too small to matter. If your power supply has a rating of 120v, it actually has a range of 110 to 125v.
Can you plug a 110v lamp into a 220v outlet?
Wire manufactured with insulation sufficient for 110 volt lamps will work on 220 volts. It would not be approved by the equivalent of the Underwriters Laboratories of the host country, but it would most definitely work.
What wattage is a 120 volt light bulb?
If you multiply the volts by the amps, you get the wattage. In this case, 120 volts multiplied by 10 amps equals 1,200 watts. This holds true for any electrical appliance. If you plug in a light and it draws half an amp, it’s a 60-watt light bulb.
Can I use any light bulb for my lamp?
You can use any type of bulb for electric lights – LED light bulbs, incandescent light bulbs, fluorescent light bulbs, and so on. All light bulbs are designed to be powered by electricity.
Can you put a higher watt LED bulb in a socket?
The answer is YES. You can use an LED bulb having a higher wattage equivalent than your fixture allows — provided the LED bulb consumes less wattage than the fixture.